Â鶹tv´«Ã½

Some links to how lecture recording can enhance the student experience.

.

Introduction to Panopto

Panopto is accessed through the HUB, the University’s Virtual Learning Environment.

There are two steps to this process (step-by-step instructions are below). First, add a link to the left menu so that Panopto can be accessed from the module. Next, provision the HUB module to use Panopto. Provisioning creates a link between the module in The HUB and a folder to store the content in Panopto.

Step 1. Add Panopto to the left hand menu

1. Go the module in the HUB where you want to add Panopto.
2. Check Edit Mode in the right of the top tab is ON.
3. Click on the + symbol in the top left of the menu.
4. Select Tool Link.
5. In the Name field add Panopto Video
6. From the Type drop down menu select Panopto Course Tool Application.
7. The link will appear at the bottom of the left menu.
8. Hover over the left of the Panopto link until a four headed arrow appears, click and drag the link up to sit within the learning and teaching area of your menu.

Step 2. Provision the course

1. Click on the Panopto link in the left menu.
2. You will then see a message that the course is not provisioned.
3. Select the Configure button.
4. On the next window that opens, select Add Course to Panopto.
5. Once the course has provisioned a provisioning result window will appear.
6. You can use the Configure more folders to associate more Panopto folders with this course. This may be useful if you are sharing the same content across multiple modules.
7. Select Return to Course.

Go to your module in the HUB and click on the Panopto Video link on the left menu.

Click theÌýCreateÌýoption on the top panel after choosing your folder, then selectÌýUpload MediaÌý

The desktop recorder needs to be downloaded and installed, see information below. Alternatively you can use the which is web based and requires no install.

Â鶹tv´«Ã½ Device owners

The Panopto software requires administrative rights to install the application on your devices. if you could please contact helpdesk@qmu.ac.ukÌýfor an incident to be raised and a member of the Technology team can assist you remotely to enable the software to be installed on your device.

On campus Â鶹tv´«Ã½ PC devices

The Panopto software has been installed on all Teaching and the larger Meeting Room devices on campus as standard. There will be announcements soon regarding how to book time in the meeting rooms and any precautions required during the current pandemic.

Personal Devices

If you have your own device that does not require administrative rights to install software then you can install the Desktop recorder as below:

1. Go to a module in the HUB where you have added the tool link to the module.
2. Click on the Panopto link on the left menu to open Panopto in the Hub.
3. Select Create and then Select Record a new Session.

A new window opens with an option to download Panopto. Download and install as you would any other application.

If you are unable to download the desktop recorder then you can create recordings using Panopto Express. Panopto Express works completely in-browser with no install of software. Once you have finished recording you can download your recording or share the recording to your Panopto account. Once the video is in Panopto you can edit it.Ìý

Find out more at

Open and start recording at ​

When you create a recording via the Hub link, it will be saved in the associated folder in Panopto.

1. Open Panopto from the left hand menu link in your HUB Module.
2. Click on Create, Select Record a new session
3. The Panopto desktop recorder will open.
4. The folder to which the recording will save is shown in the Folder field.
5. In the Name field, add a meaningful name for the recording.

Panopto overview of

Trim

You may wish to trim out the start or end of a video. The bits that you cut out are not lost and can be added back in later.

Watch a short video on

The course rollover process will create and set-up a folder on the Panopto for the next years module, but the content of the folder will not be copied over.

Links that were created on content areas on the previous year’s module will roll over and be accessible to students on the new module. Embedded videos and links to Panopto videos that are part of the content are will rollover and be accessible.

There are two methods that can be used for rolling over Panopto content. Information and step by step guidance is available below.

Panopto has a smart video Search Engine.

In the Panopto interface you can search for key words and skip to where these appear. Type the word into the search field and Panopto will search through every spoken word, words displayed on the screen and in slides.

Watch a short video on

Notes

Panopto's note taking ability gives you the ease of typing out notes on the video on the same page as you watch. Your notes will appear time-stamped right along with the part of the video that corresponds with it. You can take notes for your own private use, share notes publicly or with specific groups of users.

Watch a short video on

Discussions

DiscussionÌýadds the option for logged in users to leave feedback or general commentary that everyone who can watch theÌývideoÌýcan see.

Watch a short video on

Quiz

In-video quizzesÌýcan test comprehension, reinforce key concepts & improve knowledge retention. They are also aÌýway to gauge student understanding and engagement with your Panopto videos. InÌýPanoptoÌýyou have the ability to addÌýquizÌýquestions to any Panopto video at any point during the presentation.

Add Captions

You can add ASR (automatic speech recognition) generated captions to your Panopto sessions.

Step by step instructions on

Watch a

Viewing the Captions

Target completion time for videos one hour or shorter:Ìý8 hours
Target completion time for videos overÌýan hour:ÌýOne day

If the video has subtitles, also called Closed Captions, you will see the CC button on the bottom of the screen. You can press this to open the captions.

Watch a short video on

A Blackboard assignment drop-box can be set up to enable students to submit a video assignment through the HUB.

The module must first be configured to use Panopto as this creates a folder on the Panopto server to hold all video files associated with the module, see

Follow the instructions below or watch a short video on

Create the HUB assignment drop-boxÌý

You can watch a short video on or follow the step by step instructions.Ìý

• In the assessment content area click on Assessments then select Assignments from the drop-down menu.
• Next select Add Content + symbol in a circle, on the bottom row of the editor. If the Add Content option is not visible, click on the three dots on the top right first to expand the tool bar.

• Under Additional Tools, select Panopto Student Video Submission.

• This will pre-populate the instruction box with the instructions for students.
• Set up any other required Ìýfields for the assignment, Points Possible must contain a value.

Closing an Assignment FolderÌý

Once all students have submitted to the assignment folder, or the deadline for the assignment has been reached, you can close the assignments folder. To do so, select the cog wheel icon in the upper right corner to open theÌýfolder SettingsÌýmenu.

(opens in new window)

Ìý

Login to Panopto and view

If you are having issues viewing a video check the

Email helpdesk@qmu.ac.ukÌýif you have any questions that are not answered here.

Book onto a Panopto session on the